This wiki has undergone a migration to Confluence found Here

Difference between revisions of "FHIR Guide to Authoring Resources"

From HL7Wiki
Jump to navigation Jump to search
Line 89: Line 89:
  
 
This tab contains the following columns:
 
This tab contains the following columns:
* "Binding Name", a string
+
* "Binding Name", a string. Must begin with an Uppercase letter
 
* "Definition", a string
 
* "Definition", a string
 
* "Binding", a choice. Allowed values are:
 
* "Binding", a choice. Allowed values are:

Revision as of 06:50, 13 April 2013

This is the technical documentation that describes what you do to author a resource that will be part of the FHIR specification. There is a also a Design Guide that addresses how resources should be designed.

Note: before attempting to author resources, you MUST be able to successfully run the FHIR build process.

Background

All FHIR resources have both a lower camel case name [name], and an upper camel-case name [Name]. Each resource has a sub-directory [name] in the source folder of the FHIR svn hierarchy, which contains all the files related to the resource. The build process looks for the following files:

  • an excel spreadsheet [name]-spreadsheet.xml that defines the content and behavior of the resource
  • several xhtml files that allow additional text documentation to be added for the resource
    • [name]-notes.xml - text documentation that goes below the formal resource definition on the resource page
    • [name]-introduction.xml - text documentation that goes above the formal resource definition on the resource page
    • others yet to be documented
  • one or more [name]-(whatever)-example.xml which is an example of the resource (refer to #Example Elements Tab for guidance on naming example files.

Only the first file must exist, though at least one example must exist. Managing examples is discussed further below.

Creating a new resource

Creating a new resource is only done by the FHIR project team once a new resource has been proposed and accepted. This section documents the process that the project team follows. paths are relative to the source directory.

  1. test and make sure your local copy of the build process completes without errors (so that if something breaks, you can be condident it's your fault . . .)
  2. create the directory [name] in the source directory
  3. copy /template/template-spreadsheeet.xml to /[name]/[name]-spreadsheet.xml (and open it, and replace "Template" in the first column of the Data Elements tab with [Name])
  4. copy /template/template-html.xml to /[name]/[name]-notes.xml and /[name]/[name]-introduction.xml
  5. copy /template/template-example.xml /[name]/[name]-example.xml
  6. add the new directory and its files to SVN
  7. edit /fhir.ini
    1. add [name]=[Name] to the [resources] section
    2. add [name]={desc} to the [status] section. desc is agreed as part of the resource proposal
  8. for some special resources, you may need to register the resource in /navigation.xml. But not for normal resources
  9. test and make sure the build completes without errors
  10. commit all changes to SVN

Excel Spreadsheet

The Excel spreadsheet contains the main logical definitions of the resource. In order to support version control, and other forms of text processing, the spreadsheet is stored as an XML document. In Excel, this format is chosen by saving as an XML Spreadsheet 2003. Any other software that can edit this format (i.e. OpenOffice) can also be used. It's even possible to use a text editor, though this is not recommended. (Note: the project team is not committed to Excel. Alternatives can be considered, as long as the same logical content can be defined).

The Excel spreadsheet contains the following tabs:

  • Data Elements - defines the actual contents of the resource
  • Invariants - documents additional rules about the resource such as co-occurrence constraints
  • Events - defined messaging events for the resource
  • "Search" - defined search parameters for the restful interface
  • "Examples" - define multiple examples for the resource
  • "Bindings" - vocabulary bindings for the resource contents

The order of the tabs is not important, and other tabs can be defined. Except as documented below, other tabs are ignored. In addition, for every page, additional columns can be defined at the discretion of the editor; they will be ignored by the build process. Additional rows other than those containing the defined contents cannot be added.

Data Elements Tab

Examples Tab

The Examples Tab lists the details for example files for a resource. If the tab does not hold any references to examples, the resource's source directory will be search for a file ending in "{resourcename}-example.xml" and this file is then used as an example instead.

The tab can contain the following columns:

  • "Name", A string, may not be empty.
  • "Identity", a string.
  • "Type", a choice. Allowed values are:
    • (empty) or "xml"
    • "csv"
    • "tool"
  • "Description", a string, may not be empty.
  • "Filename", a string, may not be empty.
  • "In Book", a boolean.

Search Tab

The Search tab contains the search operations for a resource. The standard search operations $page, $count and $id do not need to be specified, but are added automatically.

The Search Tab has the following columns:

  • "Name", a string. May not end in "-before" or "-after", these suffixes are automatically added for time-based searches.
  • "Description", a string.
  • "Type", a choice. Allowed values are:
    • "integer"
    • "string"
    • "text"
    • "date"
    • "token"
    • "qtoken"
  • "Repeats", a choice. Allowed values are:
    • "single"
    • "union"
    • "intersection"

Bindings Tab

The Binding tab contains the definition of the Bindings as mentioned in the definition of the data elements. The Binding column in the Data Elements Tab refers to the Binding Name.

This tab contains the following columns:

  • "Binding Name", a string. Must begin with an Uppercase letter
  • "Definition", a string
  • "Binding", a choice. Allowed values are:
    • (empty) or "unbound"
    • "code list"
    • "special"
    • "reference"
    • "value set"
  • "Binding Strength", a choice. Allowed values are:
    • (emtpy) - Unstated
    • "required"
    • "preferred"
    • "suggested"
  • "Extensibility", a choice. Allowed values are:
    • (empty) or "complete"
    • "extensible"
  • "Reference", a string
  • "Description", a string

In case the Binding is of type "code list", the column "Reference" must contain the name of another tab containing the valueset for this binding, prefixed by '#'. This tab may contain the following columns:

  • "Code", a string.
  • "Display", a string.
  • "System", a string.
  • "Definition", a string.
  • "Comment", a string